亚洲不卡的视频一区在线播放|乱码av一区二区三区四区|av电影在线不卡一区二区|麻豆成人精品一区二区三区

歡迎光臨:

昆明惠博電纜橋架廠

是云南昆明地區電纜橋架、玻璃鋼橋架、各種母線槽等產品的頂級橋架廠商,我們歡迎各位領導前來考察!
  • 在線聯系
  • 微信掃描

加入我們的企業QQ

點擊這里給我發消息

搜索我們微信公眾號:*****

聯系我們 contact us
17387187921
電話:
17387187921
地址:
昆明市官渡區東聚建材城東區6幢13號
行業知識
您所在的位置:首頁 > 行業知識 > 正文

梯形電纜橋架橫檔標準

作者: 來源: 日期:2022/4/6 19:55:44

梯形電纜橋架一般由底板、橫檔、蓋板和連接片組成,橫擔通過焊接固定在兩邊的側板上,側板加橫檔成為橋架的主體結構,原來橋架橫檔都是橋架生產廠家自己生產,JB/T 10216-2013 電控配電用電纜橋架標準(下面簡稱2013標準)中對于橫檔的標準要求作了相關規定。下面北京京運偉業電纜小編就給大家具體介紹一下:  云南鍍鋅梯形橋架.png

標準1

橫檔與橫檔之間的距離一般為不應大于300mm,距離再寬的話,就無法滿足橋架的安全載荷標準要求,參照2013橋架標準,一節2米的梯式橋架如果高度為100mm,則其每米載荷的標準要求為1000N,如果為高度為200mm,則其每米的標準要求載荷為3100N。

標準2

橋架橫檔的厚度應該與橋架側邊的厚度為同一等級,例如橋架側邊板材的厚度標準為1.5mm,則橋架橫檔板材的厚度標準也應該為1.5mm,當然也可以選擇2.0mm厚一等級,電纜橋架制造廠家從成本方面考慮,很少會用厚一等級的橫檔。

標準3

橋架橫檔的寬度一般為40mm,敷設在梯式橋架上的電纜與橫檔的接觸寬度不要小于25mm,這是2013標準中關于接觸面積的要求,如果接觸面積過小,會導致橋架單個橫檔的承載載荷過大,導致橫檔撓度值過大發生彎曲變形,焊的不好的話這個橫檔還會掉落。

Trapezoidal cable bridge is generally composed of a bottom plate, a rail, a cover plate and a connecting piece. The cross arm is fixed on the side plate on both sides by welding. The side plate plus the rail becomes the main structure of the bridge. JB/T 10216-2013 Electrically controlled distribution cable tray standard (hereinafter referred to as 2013 standard) has made relevant provisions for the standard requirements of the transverse. The following Beijing Jingyun Weiye cable xiaobian will give you a specific introduction:

Standard 1

The distance between the crossbar and the crossbar should not be greater than 300mm. If the distance is wider, it cannot meet the safety load standard requirements of the bridge. Referring to the 2013 bridge standard, a 2 meter ladder bridge if the height is 100mm, the standard requirements of the load per meter are 1000N. If the height is 200mm, the standard load per meter is 3100N.

Standard 2

The thickness of the bridge rail should be the same grade as the thickness of the bridge side, for example, the thickness standard of the bridge side plate is 1.5mm, then the thickness standard of the bridge rail plate should also be 1.5mm, of course, you can also choose a grade of 2.0mm thick, cable bridge manufacturers from the cost point of view, rarely use a grade of thick rail.

Standard 3

Bridge generally is 40 mm, the width of rail laying on the ladder type cable on the bridge and the rail contact width is not less than 25 mm, this is about the contact area in 2013 standard requirements, if the contact area is too small, can lead to bridge the bearing load of a single rail is too big, cause a bending deformation of the rail deflection value is too large, the rail welding is not good words will fall off.




聯系我們 contact us
 
手機:
17387187921
 
微信:
17387187921
 
郵箱:
[email protected]

聯系我們

Contact Us

電話:+86-17387187921
地址:昆明市官渡區東聚建材城東區6幢13號

友情鏈接: